Printed dual-band base station antenna for GSM/DCS/PCS/UMTS and LTE applications with dual polarization

A new design of the dual-band and dual-polarized base station antennas for supporting the mobile communication systems operating at the GSM/DCS/PCS/UMTS and LTE frequency bands is presented. A wide input impedance matching bandwidth is achieved due to a trident-shaped feeding technique. Two printed dipoles, which are located perpendicularly to each other and fed by stepped-microstrip lines, establish the proposed antenna. In addition, by locating a low-profile cavity-backed structure, as a metal reflector under the antenna, bidirectional radiations of the dipoles are switched to unidirectional radiations with an increase in the gain of the antenna. Measurement results indicate that the proposed antenna is suitable for base station applications at the operating frequencies of 800/900/1800/1900/2300 MHz. The isolation is better than 20 dB, and peak gains of 10.08 and 9.96 dBi are attained at port-1 and port-2, respectively. Furthermore, the HPBWs of the antenna in H-plane is more than 61° for each port. The overall dimension of the antenna is 168 × 168 mm², which is mounted upon a 222 × 222 mm² cavity-backed structure with a depth of 42 mm.     

Empirical evaluation of river basin sustainability affected by inter‐basin water transfer using composite indicators

In this study, a practical approach to evaluate the sustainability of river basins subjected to an inter‐basin water transfer project is developed. Selection of appropriate evaluation indicators is pivotal to such approach. To make use of huge amount of data, composite indicators of sustainability (CIS) should be utilised. The proposed approach relies on 15 sustainability indicators (SI) that cover three major criteria namely (economic, social and environmental), and aggregates them into eight different types of sustainability indices for a more robust outcome. Two scenarios were considered within the source and recipient basins. Furthermore, multivariate principal component analysis (PCA) was applied to determine principal and non‐principal indicators for the two river basins. The ability of CIS and PCA methods were verified via correlation and simple regression methods respectively. The results demonstrated that inter‐basin water transfer may improve sustainability, provided that a proper water resource management is enforced.     

Fault diagnosis of an automobile cylinder head using low frequency vibrational data

This paper proposes a vibration-based fault-diagnosis method for mechanical parts. This method, after algorithm development, only requires a single inexpensive test to inspect the part which could take as short as half a second. The algorithm is developed in three major stages, (i) exciting specimens without or with known faults using a controlled force and recording acceleration of a single point for a short time (ii) finding a signature for each faulty specimen, using Fourier transform and statistical analysis. (iii) Developing a multi-layer perceptron, as a mathematical model, using the results of stage (ii). The elements of a part signature are the inputs to the model. The location (and possibly size and shape factor) of the fault is model output. Stage (i) can be performed experimentally or alternatively with a validated FEM, one experiment or simulation per specimen. The proposed technique was examined to locate (isolate) a fault on an automobile cylinder head. The presented accuracy is considerable, and the data collected at fairly low frequency range (below 1200 Hz) were found to be sufficient for this technique. In the case study of this paper, possible fault locations are on a line; as a result, fault location has one dimension. It is shown that the technique can be extended to higher dimensions.     

Feldspar/titanium dioxide/chitosan as a biophotocatalyst hybrid for the removal of organic dyes from aquatic phases

Feldspar/titanium dioxide/chitosan hybrid, a photoactive biocompatible adsorbent for anionic dyes, was synthesized, characterized, and successfully tested. The adsorbent characterization, pH role, adsorbent dose effect, equilibrium data, kinetic plats, and thermodynamic parameters are reported. The point of zero charge for the hybrid was measured to be 8.3, and the most favorable pH range for the adsorption process was found to be below this pH value. The adsorption equilibrium study demonstrated that the Freundlich model was best fitted to the experimental data. Without UV light exposure, the prepared adsorbent adsorbed 72 mg of Acid Black 1 (AB1)/g of sorbent (86% removal) from a 100‐mL solution with an initial dye concentration of 50 mg/L, whereas UV irradiation resulted in an increase in the elimination of AB1 dye (97% removal). The kinetic data was depicted well by the pseudo‐second‐order model. The thermodynamic parameters indicated that the reaction between the hybrid and the dye was exothermic and also spontaneous at lower temperatures. In the batch desorption process, several aqueous solutions adjusted to different pH values were tested, and the best desorption performance (90% desorption) was achieved at pH 11. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40247.     

Rheological,crystal structure,barrier, and mechanical properties of PA6 and MXD6 nanocomposite films

In this study, rheological, crystal structure, barrier, and mechanical properties of polyamide 6 (PA6), poly(m‐xylene adipamide) (MXD6) and their in situ polymerized nanocomposites with 4 wt % clay were studied. The extent of intercalation and exfoliation as well as type of crystals, crystallinity, and thermal transitions were investigated using X‐ray diffraction (XRD) and differential scanning calorimetry (DSC), respectively. Dynamic rheological measurements revealed that incorporation of nanoclay significantly increases complex viscosity of MXD6 nanocomposites at low frequencies, which was related to the formation of a nanoclay network and exchange reaction between MXD6 chains. The comparative study of dynamic characteristics (G′ (ω) and G″ (ω)) for aliphatic and aromatic polyamide nanocomposites with their neat resins as well as the relaxation spectra for both polymer systems confirmed the possibility of the aforementioned phenomena. Although, the crystallinity of MXD6 films was lower as compared to PA6 films, the permeability to oxygen was more than 5 times better for the former. Incorporating 4 wt% clay enhanced the barrier property, tensile modulus, and yield stress of PA6 and MXD6 nanocomposite films in both machine and transverse directions without sacrificing much puncture and tear resistances. The PA6‐based films showed higher tear and puncture strength as compared to MXD6 films. POLYM. ENG. SCI., 54:2617–2631, 2014. © 2013 Society of Plastics Engineers     

Numerical investigation on the number of active surface sites of carbon catalysts in the decomposition of methane

The number of active sites on the surface of carbon catalysts is an important factor in determining their activity in the decomposition of methane. Although several studies have been performed to identify the nature of these sites, no method has been established to estimate their number. A method is presented to estimate this value, and its effect on hydrogen production is evaluated, along with that of temperature and residence time. For this purpose, the thermocatalytic decomposition of methane is modeled with the inclusion of the number of active sites of the catalyst in the kinetics. The results of the model indicate the high influence of variations of small residence times in this process, and the reduction of this effect at high temperatures. Also, the effect of the number of surface sites is shown to be more prominent at low residence times and temperatures. © 2014 American Institute of Chemical Engineers AIChE J, 60: 2228–2234, 2014     

Chemical vapor deposition of poly(3‐alkylthiophene) nanoparticles on fabric: Chemical and electrochemical characterization

Chemical vapor deposition of poly(3‐methylthiophene) and poly (3‐hexylthiophene) as conductive polymers on the surface of polyester fabrics was successfully obtained. Fourier transform infrared spectroscopy confirmed the formation of polymers on surface of fabrics (the fingerprint of polythiophenes, υ 600–1500 cm^?1). The uniformity of deposition and nanoparticles (average size of 60 nm) were proved with scanning electron microscopy. Electrochemical impedance spectroscopy showed that P3HT‐coated samples offer higher conductivity in compared to P3MT‐coated samples. The impedance modulus of P3HT‐coated samples was lowered nine times to that of row materials and reached to c8000 Ω. The samples have also shown electrochromic properties under electrical current, changing its color from yellowish green at 0 V to dark green at +12 V for poly (3‐hexylthiophene) samples and from brown at 0 V to red at +12 V for poly(3‐methylthiophene)‐coated fabrics (V = 0 V, λ = 450 nm; V = 12 V, λ = 650 nm). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40673.     

The effect of substrate surface integrity on the surface properties of TiCrN coating applied via the CAE-PVD method

This study aims to investigate how the predeposition machining processes such as magnetic grinding, turning machining, and wire electrical discharge machining can influence the surface properties including electrochemical and tribological behavior of TiCrN nanostructured coating applied on Mo40 steel substrate. A physical vapor deposition technique using cathodic arc evaporation was used to apply the coating. The crystallographic phases and the microstructure of the coating were studied by X-ray diffraction and scanning electron microscope, respectively. Rockwell-C, electrochemical impedance spectroscopy and potentiodynamic polarization, and pin-on-disk wear tests were employed to evaluate the adhesion strength, corrosion behavior, and tribological property of specimens, respectively. The electrochemical results after 24 h of exposure to 3.5 wt% NaCl solution showed that TiCrN coating pretreated with a turning process with polarization resistance of about 3525.32 Ω.cm² had the best corrosion resistance among all specimens. This was because of the improvement of the smoothness, surface quality, and adhesion after the turning process. On the other, the friction coefficient of the grounded sample is less than that of other ones. This is probably due to its higher adhesion strength and higher surface smoothness.     

CuI Immobilized on Tricationic Ionic Liquid Anchored on Functionalized Magnetic Hydrotalcite (Fe3O4/HT-TIL-CuI) as a Novel,Magnetic and Efficient Nanocatalyst for Ullmann-Type C–N Coupling Reaction

One of the most important reactions in organic synthesis is Ullmann-type C–N coupling reaction which has been used for preparation of numerous biologically active compounds. In this work, CuI immobilized on tricationic ionic liquid anchored on functionalized magnetic hydrotalcite (Fe₃O₄/HT-TIL-CuI) has been successfully prepared and fully characterized by different techniques, including fourier-transform infrared spectroscopy, vibrating sample magnetometer, thermo gravimetric analysis, transmission electron microscopy, field-emission scanning electron microscopy, energy dispersive X-ray spectroscopy, elemental mapping, zeta potential, X-ray diffraction, temperature programmed desorption of ammonia (NH₃-TPD), temperature-programmed reduction and inductively coupled plasma. The results showed that the as-prepared nanocatalyst possesses plate-like morphology with approximate size of 50 nm and superparamagnetic behavior. Also, total acidity and total hydrogen consumption of the nanocatalyst were measured to be 8.5 and 1.41 mmol g^?1, respectively. This nanocatalyst exhibited favorable performance for C–N coupling reaction among a variety of aryl halides and N(H)-heterocycles (benzimidazoles, pyrazoles and triazoles) in the presence of 2.5 mol% of nanocatalyst without any additives under air atmosphere revealing high yields in all cases. Besides, it is noted that in the present system the desired product can be easily and quickly isolated and nanocatalyst also recovered magnetically from the reaction mixture employing a permanent magnet for at least six consecutive trials without a discernible decrease in catalytic activity which makes the proposed methodology appropriate for industrial. The findings demonstrated the advantages of the present method as no need for neutral atmosphere, appropriate times, recyclability of the catalyst, broad substrate scope, minimization of chemical waste, simple purification of products, easy workup process, and high yields.

     

A Proteomic Analysis of Human Follicular Fluid: Comparison between Younger and Older Women with Normal FSH Levels

The follicular fluid (FF) is produced during folliculogenesis and contains a variety of proteins that play important roles in follicle development and oocyte maturation. Age-related infertility is usually considered as a problem that can be solved by assisted reproduction technology. Therefore, the identification of novel biomarkers that are linked to reproductive aging is the subject of this study. FF was obtained from healthy younger (20–32 years old) and older (38–42 years old) women undergoing intracytoplasmic sperm injection (ICSI) due to male factor infertility. The FF was analyzed by two-dimensional gel electrophoresis (2-DE). The power of two-dimensional gel electrophoresis and the identification of proteins were exploited using matrix-assisted laser desorption-ionization time-of-flight/time-of-flight (MALDI-TOF-TOF) mass spectrometry. Twenty three protein spots showed reproducible and significant changes in the aged compared to the young group. Of these, 19 protein spots could be identified using MALDI-TOF-TOF-MS. As a result of MASCOT search, five unique downregulated proteins were identified in the older group. These were identified as serotransferrin, hemopexin precursor, complement C3, C4 and kininogen. A number of protein markers were found that may help develop diagnostic methods of infertility.